Maven 50ml Empty 2:1 ratio 2-Part Cartridge with sealing cap & pistons (2:1 mix

Description: Maven 50ml Empty 2:1 ratio 2-Part Cartridge with sealing cap & pistons (2:1 mix ratio) Maven 2-Part (dual-component) 2:1 ratio 50ml empty Adhesive Cartridges with included Reseal-able Cap and Sealing Pistons. Used for filling and dispensing 2-part adhesives, epoxies, silicones, urethanes, and other 2-part fluids and compounds. Direct Substitute and Replaceable for Sulzer MixPac Cartridge Part Number: AA 050-02-10-01 (#111201) Nordson EFD Part Number 7702886 (aka BS-101-01). Available in 3 kit packages, plus Accessories: Empty Cartridges and related Pistons Starter Kit with Small Hand Plungers Starter Kit with Dispenser Useful Additional Accessories Each kit includes different cartridge-count options… either 5, 10, 25, 50, or 100 cartridges with the necessary cap and sealing pistons to close and seal the empty cartridges. About the Cartridges: These cartridges are for storing and applying adhesives that use a 2:1 mix ratio, where precise metering and mixing is needed. These cartridges include matching pistons and a re-sealable tip (or cap). They’re ready for filling with material, storing and dispensing. These 2-Part cartridges are industrial grade and silicone free. The cartridge design/fit using the "A-System", also known as "Square-Back". They also include an easy-to-reclose cap. The 2-Part design keeps the two adhesive parts separate, until a mixing nozzle is attached, where the two parts are pushed or extruded into the mixing nozzle and bonding or curing begins. And a key feature of this cartridge is it's easy-to-install pin-style sealing pistons, which allows air to escape as pistons are inserted, and then seals-off with the push of the blue pin. About the Starter Kits: Each Starter Kit includes either 5, 10, 25, 50, or 100 cartridges, related sealing pistons and cartridge caps, mixing nozzles (one nozzle for each cartridge in your kit), and either one 50ml dispenser or small hand plungers depending on which kit you choose. We recommend checking out our Starter Kits to get set up and running. Or if you prefer getting the dispenser separately, check out the MixPac DMA50 50ml Dispensers, which will enable you to dispense the adhesives out of these cartridge kits. Total Cartridge Length (bottom to cap tip 4 5/8 inches Barrel length 3 13/16 inches Total cartridge width 1 7/8 inches Large Barrel Inner Diameter 0.87 inches Small Barrel Inner Diameter 0.62 inches Mixer Style Bayonet 50ml, Helix or Quadro/Square Total Cartridge Volume (both barrels combined) 50ml , or 1.7oz NOTE: Additional accessories needed. Consider the pre-configured starter kits, or view the accessories scroll-bar below to ensure you get what you need. For example, with these empty cartridges you will also need mixing nozzles and a dispensing product to push/extrude/dispense the adhesive out. We recommend also getting one of our 50ml Dispensers, which will enable you to dispense the adhesives out of these cartridge kits. The mixing nozzles needed are of the "bayonet" design, which easily twist on and off the cartridge end. These nozzles tend to be difficult to clean and store after their first use, and therefore generally considered to be single-use accessories. These Cartridges use standard static mixer nozzles. Cartridges available in mix ratio's 1:1, 2:1, 4:1 and 10:1. Products are industrial grade safe to 100 psi and are certified silicone free. Dispensers are available for all size cartridges either in manual of pneumatic. The “A” System is comprised of a small lightweight, hand-held manual dispenser which dispenses 2-component adhesives through “B” System cartridges and motionless mixers. Cartridge systems are available in a variety of volumetric ratios. Please be sure to select the correct ratio for your two component system. Maven 50ml Empty 2:1 ratio 2-Part Cartridge with sealing cap & pistons (2:1 mix ratio) Maven 2-Part (dual-component) 2:1 ratio 50ml empty Adhesive Cartridges with included Reseal-able Cap and Sealing Pistons. Uséd for filling and dispensing 2-part adhesives, epoxies, silicones, urethanes, and other 2-part fluids and compounds. Direct Substitute and Replaceable for Sulzer MixPac Cartridge Part Number: AA 050-02-10-01 (#111201) Nordson EFD Part Number 7702886 (aka BS-101-01). Available in 3 kit packages, plus Accessories: Empty Cartridges and related Pistons Starter Kit with Small Hand Plungers Starter Kit with Dispenser Useful Additional Accessories Each kit includes different cartridge-count options… either 5, 10, 25, 50, or 100 cartridges with the necessary cap and sealing pistons to close and seal the empty cartridges. About the Cartridges: These cartridges are for storing and applying adhesives that use a 2:1 mix ratio, where precise metering and mixing is needed. These cartridges include matching pistons and a re-sealable tip (or cap). They’re ready for filling with material, storing and dispensing. These 2-Part cartridges are industrial grade and silicone free. The cartridge design/fit using the "A-System", also known as "Square-Back". They also include an easy-to-reclose cap. The 2-Part design keeps the two adhesive parts separate, until a mixing nozzle is attached, where the two parts are pushed or extruded into the mixing nozzle and bonding or curing begins. And a key feature of this cartridge is it's easy-to-install pin-style sealing pistons, which allows air to escape as pistons are inserted, and then seals-off with the push of the blue pin. About the Starter Kits: Each Starter Kit includes either 5, 10, 25, 50, or 100 cartridges, related sealing pistons and cartridge caps, mixing nozzles (one nozzle for each cartridge in your kit), and either one 50ml dispenser or small hand plungers depending on which kit you choose. We recommend checking out our Starter Kits to get set up and running. Or if you prefer getting the dispenser separately, check out the MixPac DMA50 50ml Dispensers, which will enable you to dispense the adhesives out of these cartridge kits. Total Cartridge Length (bottom to cap tip 4 5/8 inches Barrel length 3 13/16 inches Total cartridge width 1 7/8 inches Large Barrel Inner Diameter 0.87 inches Small Barrel Inner Diameter 0.62 inches Mixer Style Bayonet 50ml, Helix or Quadro/Square Total Cartridge Volume (both barrels combined) 50ml , or 1.7oz NOTE: Additional accessories needed. Consider the pre-configured starter kits, or view the accessories scroll-bar below to ensure you get what you need. For example, with these empty cartridges you will also need mixing nozzles and a dispensing product to push/extrude/dispense the adhesive out. We recommend also getting one of our 50ml Dispensers, which will enable you to dispense the adhesives out of these cartridge kits. The mixing nozzles needed are of the "bayonet" design, which easily twist on and off the cartridge end. These nozzles tend to be difficult to clean and store after their first use, and therefore generally considered to be single-use accessories. These Cartridges use standard static mixer nozzles. Cartridges available in mix ratio's 1:1, 2:1, 4:1 and 10:1. Products are industrial grade safe to 100 psi and are certified silicone free. Dispensers are available for all size cartridges either in manual of pneumatic. The “A” System is comprised of a small lightweight, hand-held manual dispenser which dispenses 2-component adhesives through “B” System cartridges and motionless mixers. Cartridge systems are available in a variety of volumetric ratios. Please be sure to select the correct ratio for your two component system. × × × × × × × × × Shipping info Click the Shipping & Payments tab above the listing description for more info Click the Shipping & Payments tab above the listing description for more info! Additional delivery notes PICK UP OPTION Sorry, our items are NOT available for pick-up. PAYMENT Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay. We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus). The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws. Thank you for shopping with us on eBay! Paying via Direct Deposit Simply add the freight cost to the item cost and forward the total amount to the address to be provided following your purchase. Additional Information No additional information at this time Ask seller a question You might also like Flow Restrictor Insert Adapter (301631) for larger cartridges - 200ml, 400ml, 60 Broker Fee for Import Customs Clearance Service Certificate of Compliance (COC) Contact To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist. Ask seller a question © Perigee Direct Shipping & Payments Click the Shipping & Payments tab above the listing description for more info Payment Accepted Payment Methods Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay. We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus). The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws. Thank you for shopping with us on eBay! Returns Returns are accepted Items must be returned within 30 days of the auction ending Buyer will pay for return shipping. eBay integration by

Price: 7.95 USD

Location: North Richland Hills, Texas

End Time: 2024-12-15T02:36:32.000Z

Shipping Cost: N/A USD