Description: SURFACE PREPARATION In virtually every application the surface to which the resin is applied MUST be well prepared to yield good adhesion. The following surface preparation procedures are recommended. METALSDegrease – Wipe laying surfaces with Methyl Ethyl Ketone (MEK) or acetone to remove all oil, dirt, and grease. Etch – For optimum results, metal parts should be immersed in a chromic acid bath solution consisting of:Sodium dichromate – 4 parts by weight Sulfuric acid – 10 parts by weightWater – 30 parts by weightThe solution should be held at a temperature of 160°F (71°C), and the parts left immersed for 5 to 7 minutes. Rinse – remove metal parts from etching bath and rinse in clean cold water (de-ionized water is recommended). If thoroughly clean, metal surfaces so treated will hold a thin film of water. Dry – To accelerate drying, items to be bonded can be placed in an air-circulating oven. ALTERNATE PROCEDUREDegrease, scour and dry – Often etching as outlined above is not practical. The surface must be cleaned by degreasing as noted above, scouring with an alkaline cleanser followed by rinsing and drying. Degrease and dry – Degrease the surface as noted above, sand or sandblast the surface lightly but thoroughly. Rinse with acetone or Methyl Ethyl Ketone (MEK), and dry.GLASSDegrease – With MEK as above, or with a strong boiling solution of a good grade household detergent. Etch – For optimum results, degreasing can be followed by the chromic acid bath outlined above. WOODSand – Bonding surfaces should be sanded lightly, but thoroughly to remove all external contamination. Clean – Carefully remove all dust, or particles of wood from sanded areas. A stiff and clean brush or compressed air can be used. PLASTICClean – Remove all dirt, oil, or other surfaces contaminated with detergent sop or degreasing solvent and water, followed by thorough rinsing and drying. A solvent that does not have a detrimental effect may also be used. Sand – Surfaces to be bonded should be sanded lightly, but thoroughly to remove surface sheen. Clean – Carefully remove all dust or particles of plastic from the sanded area. A clean brush, lint-free cloth, or compressed air may be used. DON'T FORGET OUR EPOXY MIXING KITClick The Link To Add To Orderhttps://www.ebay.com/itm/222623932456EVERYTHING YOU NEED TO MEASURE, MIX, DISPENSE OR APPLY Proportioning the correct amount is equally as important to attain the intended cured properties of the resin system. The container in which the epoxy and curing agent is mixed is an important consideration when mixing an epoxy resin system. The container must withstand the tenacity of the chemical and must be free of contamination. Most epoxy curing agent has a degree of corrosivity, as a general practice, protective gloves should be worn when handling chemicals of the same nature. MIXING KIT CONTENTS 1 Each Digital Scale -Durable, Accurate Up To 2000.0 Grams 4 Each 32-ounce (1 Quart) Clear HDPE Plastic Mix Cups4 Each 16-ounce (1 Pint) Clear HDPE Plastic Mix CupsOne Size Fits All Powder-Free Latex Gloves 2 Each Graduated SyringesWooden Stir SticksAssorted Size Foam Brush THANKS FOR STOPPING BY IMPORTANT NOTICE Your purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product.The user should thoroughly test any proposed use of this product and independently conclude satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval. The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.There is no warranty of merchantability of fitness for use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to the refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind.Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.
Price: 48.7 USD
Location: Ontario, California
End Time: 2025-01-27T02:00:58.000Z
Shipping Cost: 0.72 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Model: MAX TPC A/B
Modified Item: No
Country/Region of Manufacture: United States
Custom Bundle: Yes
California Prop 65 Warning: PROP 65 WARNING: This product contains less than 0.1% of a chemical known to the State of California to cause cancer ●EPA SARA Title III Section 313 above ‘de minimus’ level: None ●All components of this product are on the TSCA Inventory or are exempt per 40 CFR 720.30 IMPORTANT USAGE INFORMATION POSTED ON THE DESCRIPTION PAGE
Country of Manufacture: United States
PATCHING COMPOUND: FOR FIBERGLASS, WOOD, METALS, CONCRETE
Patch, Crack, Divot Repair Compound: For Fiberglass, Wood, Metals, Concrete
Cures Hard At Room Temperature: Sand, Shape, And Paint After 24 Hour Cure
Strong, Lightweight, Durable Putty: Floats On Water, High Compressive Strength
Type: Syntactic Foam Epoxy Resin
Syntactic Foam Resin System: Edge Closeout, Core Splicing, Corefill
Expiration Date: Does Not Expire
MPN: MAXTPC48OZ
Brand: MAX TPC A/B
Bundle Description: Purchase a scale with any of product offering and the shipping cost of the scale is free. Please request a total before paying for combined shipping savings. https://www.ebay.com/itm/222630300203
